標題: SOLIDWORKS,零件打包就罷工 [打印本頁] 作者: oh小二 時間: 2022-7-20 17:16 標題: SOLIDWORKS,零件打包就罷工 各位大蝦,新裝的SOLIDWORKS2019,文件在 執行PACK AND GO操作時,軟件就會奔潰,啥原因啊。0 M& M/ Q" {! P0 _ 作者: shentu 時間: 2022-7-20 17:25
怪電腦咯~作者: 鑫森淼炎垚 時間: 2022-7-20 17:53
可能是軟件安裝丟文件了,換其它版本試一下吧。作者: cool44 時間: 2022-7-20 17:53
部分裝有加密軟件的電腦會這樣,無解的。直接復制再改名。作者: 斯文棒棒 時間: 2022-7-20 18:43
2018的還沒有遇到過作者: 妖洞兩拐 時間: 2022-7-21 04:33
樓主不會用的是sp0版本吧?作者: 達文中 時間: 2022-7-21 08:48 本帖最后由 達文中 于 2022-7-21 08:51 編輯 2 F9 ^) H, k0 A; q7 c( u- n1 T0 }" F# `* y3 B' w; ~* D
之前用SolidWorks 2019,最近更新到2021,也遇到同樣的問題。' ?/ |5 h7 K" G. L! g' F
6 ~* ]" b' @- a: _" p
網上找到了解決方案,記錄如下: % q7 i0 ^. A- u" ?9 O& L7 N0 J+ @, X( ^3 x, a2 x4 M6 w
8 G- I* e/ \8 d4 X }) i5 | SolidWorks 2021 Pack and go 功能無法啟用 + u4 z4 D+ x& F! J. C- a) L% T ' H- b c: v* b) g/ MPack and Go Nothing Happens 7 ~2 e* E1 G. p7 ?6 W. k% K用戶 Gordon KistlerSOLIDWORKS User Forum2022-05-05 ' c4 J" U5 a9 z# u2 z7 B, \! TI am using SW2021 SP5.1, freshly installed by my IT department. When I try to do a Pack and Go from within SW, nothing happens. When I try Pack and Go from within Windows Explorer, I get the spinning circle but nothing else. Suggestions? + I1 J* K8 W' N4 C: g ; w1 o( \2 X7 [' Q* M; UGordon Kistler - 2022-05-09! ]$ U8 p$ F# \5 b4 Z3 d/ P' D E
Resetting the registry and then restarting SolidWorks took care of the problem. Thank you! 5 n; q2 P0 z( u* l% | 5 V7 b" E4 F0 [+ g, ~6 w' u) vLink From:<https://r1132100503382-eu1-3dswym.3dexperience.3ds.com/#community:yUw32GbYTEqKdgY7-jbZPg/iquestion:e_-F0_riRuKyo78xKK3bgQ>* O$ c7 p/ E: }% O$ D
( i! j$ r4 J" B9 r & e+ B- K$ y% Y1 g可以看到是因?yàn)樽?cè)表有問題,那怎么更改注冊表?+ L3 L9 `- `8 I/ ~" Q+ x( s" G! {/ a# [
# w" f$ Q1 }& Q3 G
How to Reset SOLIDWORKS by Resetting the Registry Entries (javelin-tech.com)3 y U9 u ~+ Z0 T1 l! l
see link <https://www.javelin-tech.com/blog/2019/01/reset-solidworks-registry/> 6 k! h/ a* Y/ m3 i6 t4 |
5 y3 W: P8 U+ e! h+ _ 作者: oh小二 時間: 2022-7-21 09:59